Cfm-corporation 7000 User Manual

O w n e r ’s M a n u a l and A s s e m b l y G u i d eFOR YOUR SAFETYIf you smell gas:1 Shut o gas to the appliance. 2 Extinguish any open ame. 3 O

Locate these parts:tools needed:3/8” open-end wrench7/16” open-end wrenchbase( 1 )Assembly Step 2 • Assemble the Pillar to Base.10pillar( 1 )1. Lock

112. Position the pillar upside down,and set the base onto the pillaras shown.Working from the open side of pillar:3. Insert four bolts through the ho

Locate these parts:tools needed:3⁄8" open-end wrench7⁄16" open-end wrench121. Place the heat shield on the pillar,aligning holes as shown.2.

13Your grill will now look like this >4. IMPORTANT:Make sure the control-valve ends areinside the burner tubes extendingthrough the grill bottom.

Locate these parts:14Assembly Step 4 • Assemble the Grill Lidtools needed:7/16" open-end wrenchflat-blade screwdriverhandle standoff( 2 )handle(

7. Raise the lid to attach the front handle.8. Attach a handle standoff to the front ofthe grill lid, as shown.9. Insert one end of the handle into th

Locate these parts:16Assembly Step 5 • Attach the Side Tables to the Grill.1. Insert 3/4" bolts throughholes in the support armsof the side table

rock grate( 1 )ceramicbriquettes( 1 box )No tools are needed.Assembly Step 6 • Install the Rock Grate and Briquettes.171. Place the single rock grate

4. Set the two porcelain coated cookinggrids on the front and back ledgesformed inside the grill bottom for alevel cooking surface.5. Set the warming

Locate these parts:1. Working from behind the grill, set thecylinder into the large round opening inthe grill base.2. Position the cylinder-retainer w

Table of Contents Page NumberChapter One - INSTALLATION 3Choosing a Safe Location 4Portable L.P. Gas Grills 5 - 6L.P. Gas Dealer Instructions 7Chapter

complete the connection, do not use this valveand regulator.7. Make sure the hose has no kinks or sharpbends and clears any areas that will become hot

DANGER: EXPLOSIVE AND FLAMMABLE!If the appliance is for connection tonatural gas, the gas connections shouldbe made by a qualified installer or alicen

OPERATING THE QUICK-CONNECTFollow all directions on tags attached to hose.1. To connect the fuel-supply hose to the fuelsupply, the shut-off valve mus

Use and Care Directions Chapter 323Leak Testing the Fuel Supply SystemLighting InstructionsReplacement PartsSeries 7000 Models

DANGER To prevent fire or explosion hazard:· Do not smoke while performing a leak test.· Do not permit any sources of ignition inthe area when testing

IGNITER LIGHTING SYSTEMThe Igniter System consists of an igniter unit,a gas-collector box, two ceramic electrodes,and lead wires. Gas is collected in

MATCH LIGHTINGIMPORTANT! The match-lighting hole is foundunder the front right corner of the grill bottom.When match lighting the grill, use the gas-c

CONTROL SETTINGSThe high flame setting is for quick searing ofmeat. Sear foods, then finish cooking on a lowersetting.A medium setting works best for

Replacement parts are available direct from our warehouse. Some components are not availablepreassembled and may be ordered separately. For convenien

Model 7000Nonly31Base AssemblyBreakdown of Preassembled ComponentsPillar AssemblyBottom/Burner AssemblyPreassembled Componentsquantity description par

Installation Chapter 13The L.P. Gas Fuel Supply SystemCorrect Filling and Handling of theL.P. Gas Fuel CylinderImportant Information Necessaryto Safel

The gas fuel used by this product ishighly flammable and must be used ina responsible and cautious manner.It is your responsibility to assemble,operat

FUEL REGULATOR AND HOSEThe fuel regulator supplied is equipped with aType 1 coupling nut. Do not attempt to connectto any other L.P cylinder not equ

DANGER: Do not insert any foreign objectsinto the valve outlet. You may damage theback check. A damaged back check cancause a leak, which could resu

Filling a Type 1 Cylinder ValveExample A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting.When using a cylinder exchange, be

Assembly Instructions Chapter 2Tools needed to assemble grill:• 3/8” open-end wrench*• flat blade screwdriver• 7/16” open-end wrench**HINT: A socket s

cooking grid(2)grill bottom(1)handle standoff ( 2 )handle ( 1 )rock grate( 1 )ceramic briquettes( 1 package )warming rack( 1 )L.P. gascylinder( 1 )cyl